Currencies:


HACKER SAFE certified sites prevent over 99.9% of hacker crime.


Search:

HOBBYMATE FPV Racing Quadcopter FC F4 Plus Racercube, W/ 4in1 BL

  • Our Price: $69.90

  • SKU: HBF4CUBE


Add to Cart: Tell a friend

HOBBYMATE FPV Racing Quadcopter FC F4 Plus Racercube, W/ 4in1 BLHeli_s ESC 30A, W/ Integrated OSD Built-in 5V BEC LC Filter, W/ Onboard 5.8G 25/100/200mW FPV Transmitter



1. Using a STM32 F405 MCU enble a faster response from the flight controller, The Omnibus AIO Pro V2 flight controller represents the     new generation of FPV racing flight controllers with loads of integrated features and performance.
2. To start the flight controller has a built in OSD which can be configured directly within the betaflight GUI.
3. The built in SD card reader means you can store all your flight logs in incredible detail to help you fine tune your quadcopter to     get the best performance out of it. Furthermore, the MPU6000 IMU runs on the SPI bus to get insanely fast readings from the IMU to     the flight controller.
4. The Pro Version uses SBEC which makes less heat than LDO version (which is used in the standard Omnibus F4); Pro Version has a       built in Current Sensor and Power Filter.
5. SBUS/PPM receiver selectabe via betaflight configurator (no resistor soldering required) Built in Voltage Sensor, Current sensor    (0m50 sensor can handle up to 200A)

HBF4CUBE-8HBF4CUBE-10


Features:
1. STM32F405RGT6 MCU, betaflight_3.1.7_OMNIBUSF4SD, could run faster loop time.
2. Using F4 MCU controls OSD over SPI bus in DMA mode.
3. OSD Configation has been included in Betaflight GUI.
4. Built-in 5V/3A BEC.
5. Built-in LC filter.
6. Support Black Box (SD card not included)
7. Spare UART3 TX3 RX3 Port
8. Pre-built camera input Port, 5V
9. Pre-built ESC Driver Signal connection port
10. Pre-Built onboard IPEX 2nd Generation Antenna Socket
11. Pre-welded beeper
12. Pre-Built DSM2/DSMX, iBus, PPM/SBUS 3-Pin Plug Socket
13. Pre-Built FPV Transmitter power and channel selection button
14. Support 2-4S Lipo Power,
HBF4CUBE-9HBF4CUBE-11
14. HOBBYMATE 30A 4in1 BLHeli_S esc, support 2-6S, Firmware BLHELI_S J_H_15_REV16_6
15. The HOBBYMATE 4IN1 ESC 30A uses the latest BB21 MCU at 48Mhz and can run the latest BLHeli_S firmware.
16. It supports OneShot, MultiShot and Dshot and in addition to this, it supports 3-6S Lipo inputs.
17. It features a built-in current sensor and LDO voltage regulator to provide a filtered and clean power supply to your flight controller and other electronics.
18. Flight Controller and ESC Standard Size: Board 36x36mm, mount holes 30.5x30.5mm;
19. Damped Light will make huge voltage spikes on LIPO side, please make sure your device works with that.

HBF4CUBE-2
Based on OMNIBUS F4, the OMNIBUS F4 Plus added SD card supports, has 5v3A BEC, LC filter for Camera and VTX, build in Current sensor for high Integration Frame, Onboard FPV Transmitter 25/100/200mW switchable, Pre-welded IPEX-II Antenna Socket

Built-in Current Sensor
On-Board Video Filter (only can supply 5V to VTX and Camera)
On-Board OSD AT7456E (controllered by Cleanflight or Betaflight (Default), FC over SPI bus)
Size: 36x36mm
Mounting hole: 30.5x30.5mm
Firmware: betaflight_3.1.7_OMNIBUSF4SD
Input voltage: 2-4S
SCM: STM32 F405 MCU
Sensor: SPI Sensor MPU6000
Slot: standard SD card slot
BEC: 5V/3A

HBF4CUBE-12
HBF4CUBE-1


Package included:
1 x F4 PLUS Flight Controller
1 x 4in1 30A esc
1 x 8P-1.0mm Connection Cable
1 x XT60 Plug
3 x 3P-1.0mm Cable
1 x 8P*1.0mm Cable